4 CH Constant Voltage DMX512 Decoder RGB/RGBW Controller Din Rail Mounted 4 Channel Dimming Controller 5-24VDC

I really like the DIN rail form factor of this Nutbro DMX decoder. They inspired me to do a complete DIN rail install for my LED and stage lighting control in my Home Theater (see attached photo). My problem is I can not get these Nutbro DMX decoders to work with my Nicolaudie STICK-CU4 DMX controller.I had a complete DMX system up running using the STICK-CU4 and the JOYLIT DMX decoders, also bought on Amazon (see photo of un-managed wiring). So I know the STICK-CU4 works with all my version one hardware and LED lights. I thought is would be as simple as swapping out the wall mounted JOYLIT DMX decoders and installing the DIN rail mounted Nubro DMX decoders. Then I would have a clean easy to manage install using the DIN rail mounting system with the plastic wire duct. I was not so lucky. As I could not get the Nutbro devices to respond to the STICK-CU4 controller.I did a quick rewire and got the JOYLIT devices to work with all the version two DIN rail install hardware. SO my DIN rail system works. Just NOT with the Nutbro devices but with the wall mounted JOYLIT devices.The Nutbro DMX decoders do work with the $49 DMX512 Show Designer lighting board, also bought on Amazon. Again this verifies that wiring is installed correctly. All the different LED lights work with all the color channels responding.In the Home Theater I need the STICK-CU4 controller as it has eight dry contact triggers. The eight triggers are hooked up to a wireless RF remote. This allows me to control the lights without getting out of my seat, when watching a movie.SO I will try debugging for a few more days , BUT for now it doesn't look promising. I most likely will be returning 4 of the 5 Nutbro DMX decoding devices that I purchased. I will be keeping one to experiment with. Who know it might start working???

These guys work great for the cost! I've got 18 of them running and led wall and other led rgbw tapes. They do take some thought to program them into our GrandMA system but we were able to get them to function perfectly.

Couldn’t get it to function at all. Using DMX or even the regular interface of pre-programmed presets.

These are great, have used many of these on installations and theatre shows over the last few years. Recently, I had a problem where some of the units seemed to need power cycling to start receiving DMX after changing address, which was very strange. But other than that, what's not to like!

Great product.Didn't try the RDM functionality but worked absolutely fine for regular DMX use.Very neat design.Nice to have a screen and buttons rather than dip switches.Love the fact it has cable strain relief and cover rather than cables hanging loose and messy like other products.

Der Dimmer funktioniert einwandfrei. Kein Flackern, sehr viele Möglichkeiten zur Konfiguration und sehr gutes Preis-Leistungs-Verhältnis.Innen befindet sich ein STM32-Microcontroller. Die MOSFETs innen haben auch anständig große Kühlkörper. PCB auch sehr sauber verarbeitet.Getestet mit der ENTTEC ODE Mk2 mit bis zu 40 DMX frames pro Sekunde.Einziges Problem ist, dass sich der Dimmer wegen der Befestigungslaschen nur schwer auf die Hutschiene spannen lässt, wenn die Hutschiene sehr flach ist. Bekommt man aber hin, wenn man die Hutschiene vom Verteilerkasten kurzerhand etwas löst bzw. abmontiert!

Klein, leicht und zuverlässig, hat ausreichend Programme und Funktionen für den Betrieb ohne DMX.Steht jedoch ein DMX-Signal zur Verfügung, schaltet er automatisch in den DMX-Modus um und tut dort das was er soll. Die vier Kanäle des RGBW-Strips dimmen. Mehr braucht es nicht.Einziger Minuspunkt: Sehr kleine (nur mit Lupe lesbare) Bedienungsanleitung und nur in Englisch.

Ottimo prodotto. Si consiglia.Provato e perfettamente funzionante, con interfaccia DOMOTICA/DMX Comelit.